Honda Civic EG6 SiR 2 - JDM - Build / Project / Restoration / Restomod / Resurrection / Bare shell rebuild / Nut & bolt Restoration


Not so very overnight parts from Japan!

Been waiting for quiet some time for these to land, took the absolute piss!! But anyways here they are.....

Honda Access OEM EG6 SiR mats

Full set of 5

Driver's side still has the little white tag on it, even though your supposed to rip it off lol

They looked okay in pics but they are actually MINT!

Absolutely over the moon with them! Got them at going rate too :)) so not to bad lol

Gonna give them a propper clean later on.

FB_IMG_1563248315428.jpg


FB_IMG_1563248317561.jpg


FB_IMG_1563248319750.jpg


FB_IMG_1563248321709.jpg


FB_IMG_1563248323750.jpg


FB_IMG_1563248325808.jpg


FB_IMG_1563248327882.jpg


FB_IMG_1563248329889.jpg


FB_IMG_1563248331930.jpg


FB_IMG_1563248334219.jpg
 
Last edited:
I took the front wings off to see what it's like, driver's side has a little bit of surface rust, passenger side has some but not as much, for some odd reason the passenger side is alot cleaner then the drivers side in general lol, maybe the drivers side was parked next to a tree or next to a drain or something, looks like alot more water has been around the drivers side.

FB_IMG_1563277747008.jpg


FB_IMG_1563277762802.jpg


Should just be able to grind it off and rust treat it.
 
Last edited:
Time to remove the sound deadening!

Bought a few cans of MOTIP Freezer spray, its basically dry ice in a can, cheaper and works alot better!

All you gotta do is spray the sound deadening, give it a couple of seconds and then get a hammer or mallet and smack it lol, and the sound deadening is off!

Really clean job, no tiny bits left over or anything, I got the whole Interior done in about an hour lol.

Unfortunately I found a couple of rust spots! One behind the driver seat, just Infront of the seam seal, and the other in the drivers footwell next to a grommet.

I also noticed that the sound deadening holds alot of water underneath, so I'm probably not going to put any back in!

Still need to get pics of the car once it's cleaned up from inside, might even weigh the sound deadening and see how much I've taken out :dance:

FB_IMG_1563277709930.jpg


FB_IMG_1563277713491.jpg


FB_IMG_1563277716424.jpg


FB_IMG_1563277720735.jpg


FB_IMG_1563277723567.jpg


FB_IMG_1563277726550.jpg


FB_IMG_1563277728806.jpg


FB_IMG_1563277775458.jpg


FB_IMG_1563277777898.jpg


FB_IMG_1563277780763.jpg


FB_IMG_1563277786946.jpg


FB_IMG_1563277794474.jpg


FB_IMG_1563277797078.jpg


FB_IMG_1563277789467.jpg


FB_IMG_1563277792234.jpg
 
Last edited:
Finally got some spare time, so I got my arches & sills and took them down to the unit and gave them a "MOCK" up lol

They aren't sat on the car properly that's why the mouldings and sills don't look flush, but they are good fitment.

Can't wait to strip it and make some progress!

FB_IMG_1563750355348.jpg


FB_IMG_1563750362372.jpg


FB_IMG_1563750368424.jpg


FB_IMG_1563750377293.jpg


FB_IMG_1563750371641.jpg


FB_IMG_1563750373829.jpg
 
Managed to get my self a Genuine Spoon N1 axle back.

Needs a little clean and a quick polish.

Not sure if I'll keep it yet as I had a Spoon N1 on my Jordan, but it'll be good for now.

FB_IMG_1567103149943.jpg


FB_IMG_1567103152195.jpg


FB_IMG_1567103154316.jpg


FB_IMG_1567103156572.jpg


FB_IMG_1567103158957.jpg
 
So today I got some time to go down to the unit, cleaned out all of the sound deadening I took off.

Probably weighed about 4-5kg I wreckon maybe a little more

FB_IMG_1569950275807.jpg


The freezer spray was pretty good, alot of the sound deadening came off in big pieces like this...

FB_IMG_1569950268025.jpg


I probably won't be putting any sound deadening back in the car, I found some water hiding under the sound deadening in the drivers foot well.

Also found 2 spots of rust again in the drivers foot well next to the grommets, not sure why the drivers side of the car has seen better days compared to the passenger side.

The way I found the rust was funny :lol: I sprayed a **** tonne of spray and I got my hammer and hit the areas of the sound deadening, and I just heard something crumble, I took the sound deadening off and seen a spot of rust, the spray freezes everything and weakens it lol which is something I should have kept in mind :lol:kind of glad that I found it tho, atleast It can get dealt with.

Alot of what you cans see in the pics is just some sort of rusty water stain that you can scrape away (drivers footwell) and the rest of the interior looks terrible, will get around to that too.


FB_IMG_1569950857040.jpg


FB_IMG_1569950860388.jpg


FB_IMG_1569950867306.jpg


FB_IMG_1569950863225.jpg


Looks alot worse than what it is, looks like some sort of rusty water stain, that you can scrape off, the actual rust is in the corner!

FB_IMG_1569950869682.jpg


Current state of the car!
FB_IMG_1569950881091.jpg
 
I was going through all of my Sh*t at home and I started to find parts from my MB6 lol

This will be perfect in the EG6 once it's on the road.

Skunk2 Neo Chrome weighted gear knob

Skunk2 Dual bend short shifter, with a spherical bearing

Skunk2 short shifter hardware kit

FB_IMG_1569951504835.jpg


FB_IMG_1569951507420.jpg


I've got some more parts laying around from the MB6 build that I need to find lol
 
I managed to buy some rare OEM optional extra goodies.

I'll let the pictures do the talking :cool:

FB_IMG_1569951778518.jpg




FB_IMG_1569951781997.jpg


These will look right at home in the EG :drool:

FB_IMG_1569951784155.jpg
 
Last edited:
Been on the hunt for some more JDM goodies again!

I got pretty lucky with finding these brooches and booklets

I've got my self a nice little collection now lol

FB_IMG_1569953913532.jpg


Absolutely LOVE the HONDA ACCESS Accessories catalogue :cool: my favourite so far.

FB_IMG_1569953915660.jpg
 
So I've been doing some digging and I've been trying to find as much history of the EG6 as I can, I already know most of the history of the car whilst it's been in England, I was after some info from when it was in Japan.

I rang Honda in Japan at stupid o' clock in the morning and tried to hustle some info out of them, using Google translate to speak to them was the best I could do, many of them found it hilarious lmao :lol: :lol: :lol:

Anyways I asked a few people , and it turns out you can do an online check with the "MLID" which is the Japanese DVLA.

I wanted to know if the car was accident free in Japan, what area it was from in Japan and also I knew it was a car from 1995, I just wanted to know what month, simply because I'm born in '95:lol::lol::lol:

So I got a detailed report emailed to me.

The car was first registered in Japan April '95, and it lived in a place called "Adachi" which is pretty much the centre of Tokyo :cool:

The car also came back straight and HPI clear, which is good to hear.

FB_IMG_1569956722371.jpg


FB_IMG_1569956724933.jpg
 
Cracking build thread, great to see a proper job being done

(p.s. im that guy of IG that bought the hornets off you last week)
 
Cracking build thread, great to see a proper job being done

(p.s. im that guy of IG that bought the hornets off you last week)

You should have the hornets by now, and you've got a sneak peak before everyone else then lol
 
You should get a build thread going too, don't think I've seen your Jordan
Was doing it as you posted that lol
 
Was doing it as you posted that lol
I'll have a look now
 
A friend of mine has a Toyota Ipsum ( Toyota Picnic JDM import) with some mechanical issue, his had it parked up for over a year.

I realised it had the plastic number plate tabs, that I need.

So like a nice guy he is, he let me nick them lol

They fit perfectly in the EG6 JDM bootlid :cool:

FB_IMG_1570398745602.jpg


FB_IMG_1570398748140.jpg
 
Back
Top