Search results


  1. jamie-gings

    EG sir oem foglight and Horn wiring

    anyone on here good with electrics and can shine some light on this . After rebuilding the eg9, i cant get the horn to work . i have located the 2 wires , the white/green is constant power , and the blue/red one becomes ground when i touch the single wire at the steering wheel to the hub (i.e...
  2. jamie-gings

    Coolant system issue

    Having an issue with my eg coupe since i swapped in an obdo b16a engine . The coolant system seems to be way too pressurized. Coolant actually sprayed all over the underside of the hood on a short drive. I noticed the fan wasnt coming on (but the needle would never go above normal)so i...
  3. jamie-gings

    EG9 nut and bolt build

    decided to restore the eg9 while im not using it as a daily driver, im about half way there atm and finally getting around to making a build thread . ben wanting to get it sprayed for a few years now as it badly needs it, so said id go all the way with it. Originally gave a timeline of 1month...
  4. jamie-gings

    Camber kits and geo setup for road cars

    Im doing a nut and bolt rebuild on my eg9 and have replaced nearly everything under the car with new parts . I'm stuck on what to do with the front and rear upper control arms . The car will mainly be a road car . It is lowered about 50mm on yellowspeed coilovers . Is it worth adding a...
  5. jamie-gings

    OEM 4.7 FD

    Looking for an oem 4.7fd + everything needed to fit it to a y21 lsd box if anyone is braking a 98 spec box drop me a pm.
  6. jamie-gings

    WTD: b18c iacv

    need an IACV from a b18c type r intake, must be working perfect anyone know of one for sale let me know, thanks
  7. jamie-gings

    Central locking issue

    The central locking isnt working in my eg9 the alarm and the key will only open the drivers door. the 3 other locks stay down however the key / alarm will lock all doors no problem when they are unlocked anyone know what could be gone , or what i need to change ?
  8. jamie-gings

    Ek rear droplinks on DC2 rollbar ??

    are all rear EK droplinks the same or are ek4/9 ones slightly different, i.e the part that bolts onto the rollbar skinnier ?? i have ek rear lcas on my eg and i have bought a dc2 rear rollbar i want to fit, so i ordered 1.4ek rear droplinks thinking all eks would be the same but they wont fit...
  9. jamie-gings

    Rear windscreen molding

    Does the rear windscreen have to come out to change the rear windscreen molding ?? can water leak into the boot if the molding isnt sealing properly at the top corners of the window ? car is an eg coupe
  10. jamie-gings

    High Comp valve clearance ??

    hi, im looking for some insight into a b16a i have. the block is b16a2 , bored to 81.5mm and fitted with pct pistons the head is a full ek9 head i had to get the head resurfaced , and got 8thou taken off. however im not sure if the head was skimmed previously so not sure exactly how much has...
  11. jamie-gings

    prelude brake master cylinder ??

    does anyone know the sizes of the 2 brake line fittings on the side of a prelude master cylinder? I just put one into my eg and one of the fittings is too big for the brake line connection. has anyone installed one of these, is there a reducer i can buy or will i have to run a new brake line ?
  12. jamie-gings

    squeaky suspension

    the suspension on my eg9 is very squeaky the front isnt too bad but the rears are v bad. sounds like its coming from the top of shocks ? anyone know what will sort this out ? the bushings at the top of the shocks seem fine but should changing these sort it ?
  13. jamie-gings

    Exhaust heat shield ?

    Just wondering is it ok to remove the exhaust heat shield underneath te car ? I had to take off my Catback recently and since iv put it back on its Ben rattling really bad when driving . Should I remove the heat shields or would I be better off gettin some heat wrap and wrap part of the...
  14. jamie-gings

    Dc2 airbox question ?

    im looking for a dc2 airbox atm and iv found one for sale but its only the box and the arm im not sure but isnt there a bracket that goes around it for fixing it to the car ? just wondering is this part essential?as its not included..... would it be easy to make up something to fix it...
  15. jamie-gings

    obd1 p30 vtec engagement?

    tried googling this and cant seem to find a definate answer. does anyone know the vtec point and rev limit for a obd1 p30 b16a sir ? i had a vafc on my eg9 which was mapped a good while ago and as far as i can remember the mapper said the vtec point was left as standard. when this was in...
  16. jamie-gings

    tracking issue ?

    ok the problem is my eg9 is pulling very bad to the left. i got a new tyre on the left side, and changed the tie rod end , then i went and got the tracking done, car was put on the ramp and adjusted till everything was in the green . however on the way home its pulling way to the left ...
  17. jamie-gings

    obd1 cel code issue ?

    ok my eg9 is after throwing up 3 codes 6-ect coolant temp sensor 15- ignition output signal 22- vtec pressure valve there car has ben off the road for a while but when driving it last week there was no codes and it ran fine. so this week i had a cel code on my project eg coupe which...
  18. jamie-gings

    oil gauge install help ?

    ok so i have an oil pressure and oil temperature gauge that i am trying to wire up but not sure what wire is for what i cant remember what make they are so cant look them up online. Both gauges are the same, they have 1 green wire , 2 black and 2 red wires i know the green wire is for the...
  19. jamie-gings

    issues after headgasket change ??

    ok so just changed the headgasket on a b16a2 and the car wont start now it starts very roughly and dies instantly i checked the timing there and seemed to be out one tooth at the crank pulley so redid the timing belt, and now as im cranking it by hand i can actually hear air escaping...
  20. jamie-gings

    doing headgasket - cant get timing belt back on ?

    ok so im just after doing the headgasket in my car when i was taking off the head i marked the timing belt and both cam gears with marker so i could line them up properly again when putting it back together and i had the engine set to tdc now i have the head and cams etc back on but cannot...
Back
Top