Search results


  1. joebarrie

    ECU problem only runs on p28

    hello, ive got a em1 b16a2 obd2 civic with a stock ecu which is (PT2) i used to run that ecu before changing to a chipped (p28) i need to run the car on the stock ecu now but its cranking but not starting, i bought a demobilizes ecu and still does not run. needing help cheers joe
  2. joebarrie

    emission to high for mot.

    Hello am having a problem with my b16a engine getting it tho a mot. The emission are to high. The standerd mid pipe and back box is new but the cat is a bit old. Tryed it first and it was reading 0. 90 c2 and I have try a nother car of a civic got it down to 0.50 and that's still not good! Ment...
  3. joebarrie

    idle problem

    Hello. I have been having a problem with my idling. Needing help. Start up cold runs about 2000rpm for 2 mins then start review from 1000 rpm to 2000rpm and does not stop! And I can't get it to go away. I have a b16a engine. I did a swap for. B16a2 to b16a using the hold throttle body and...
  4. joebarrie

    inovit wheels rays center caps???

    Hello people! I have some inovit ray wheels in white, am woddering if anyone noes of a Web side that sell the center caps for the wheels?? Cheers.
  5. joebarrie

    running rich. b16a

    My b16a motor is running rich after changing the inlet manifold. in have checked all the plugs. Plus it started to rev up to 2000rpm and drop Down and back up to 2000rpm. Replaces all the in let gaskit. Help people??
  6. joebarrie

    EM1 BOOT SEAL? where can i find a new one?

    hi am looking for a brand new boot seal for my em1 coupe civic because it leakingin, I cant seam to find any on the web cheers.
  7. joebarrie

    weekend insurance?? when 21.

    hello am 21 now and I have my civic that wanting to drive just at the weekend is there any insurance that does just weekends??? cherrs
  8. joebarrie

    recommend rods and piston for turbo

    Hello. Am wanting to forged my b16a2. But am wanting to noo what's the best pistons and rods for it. Looking for 400 hp will I need more or just pistons and rods. Would be good to here from people out there that done it before just to see how there out come is. Cheers!
  9. joebarrie

    Running very rich help?

    Hi I need abit of help. I put a b16a In my em1 I use to have a b16a2 engine in it. Put it in runs ok went to change the inlet manifold to the b16a2 manifold and now it running really rich a lot of black smoke and fuel smelling. Nothing is leaking and it run like a bag of **** when I have half...
  10. joebarrie

    cranking no start help?

    been having bother with my b16a2 not start replaced the engine with a b16a. cracks sparks and gets fuel but it just dont wont to start. the thermosat ground is the closes i have gotten, when taking it off the ground and putting on to the gound when cranking it wants to try and start for a few...
  11. joebarrie

    Engine cranking but no start! Help!?

    Hello. I have put a new engine back into my car. Last engine was b16a2 and now in the car is a b16a. It's cracking over but not wanting to run. It's getting a spark and fuel, timing is bang on. I spray brake cleaner in the Inlet manifold and it does not want to fire the slightest. Only thing I...
  12. joebarrie

    B16a JDM the same as b16a2?

    Hello, needing to no if a b16a JDM engine is the same as a b16a2? Inlet out manifolds,connectors, and gearbox the same?? Cheers joe
  13. joebarrie

    B16a2 swap to b18c4 possible??

    Hello, am wanting to swap my engine from a b16a2 to a b18c4. -do I need b18 drive shafts? -do I need b18 engine loom? -do I need to change any engine mounts? Been reading about and people has been saying you don't need to do anything?? Cheers joe :)
  14. joebarrie

    Stock b16a2 turbo psi?

    Hi I have a stock b16 turbo and I will be running it with a 8 psi waste gate spring. Was wondering would it be safe to run 8psi spring first or should I get a 5 psi spring first?? Cheers
  15. joebarrie

    ecu help!

    hello am turboing my stock b16a2 with a t3 t4 turbo. i have all the parts waiting to go on but am not sure for ecu. i have a greaddy blue box that could work but am really wanting to use it. H-TUNE do a p28 ecu with a turbo base map, would it just be as easy to buy that? and would it just the...
  16. joebarrie

    Help with injectors?

    I have bought 440cc injectors for my b16a2 and I remove the standerd ones and try to fit the new ones, it seams that it won't fit in the inlet manifold?? I noo it a different obd but am more conserned about the fitting them in? Will try and get a photo up tomorrow cheers
  17. joebarrie

    Headgaskit for b16 turbo help?

    Needing help finding a head gaskit for a b16 turbo. What think was is best for Lowering the compresion need help finding one in the UK?
  18. joebarrie

    Honda logo. D13 to a d16

    I have a small honda logo two door that has a d13 in it. Was wondering if there is anyone on here that has swapped d13 to a d16? If soo are the plugs the same so it's plug and play? And are the engine mounts the same? Cheers joe!
  19. joebarrie

    where can i find 440cc injectors??

    hi been looking for the past two days now for injectors, where can i find 440cc in the uk?
  20. joebarrie

    td04 turbo on stock b16a2?

    hi been thinking about getting a turbo kit (td04) for my em1, but does anyone no what bar you can run stock b16 on?
Back
Top