Search results

After some research i have decided I'm goin to build a g23 engine for my euroR as I'm fed up of the h22 and it's stupid frm liners, and don't want to go to the expense of sleeving it, I already have all the bits lying around to build a decent g23 but the only problem I'm having is sourcing the...

as above looking to buy a b18c type R bottem end.

as some of you who know me will know i am in the process of rebuilding my ek9 from a bare shell up, and have quite a few spare parts left over as most of it is being replaced with new parts, and while my cl1 euro R was supposed to be my sensible daily driver to keep me goin until the ek9 was...

think its about time i put up a build thread on my euro R, bought it about a year ago in standard unmolested form,...and intended leaving it alone as a nice daily driver, but that took a bit of a twist and ended up with a turbo :lol: that all went well for a few months until i spied a...

Looking for a carbon or frp bootlid for my ek9, also need a k24 block or complete engine, dc5 gearbox either damaged or perfect dosnt matter as long as I know, k-tuned billet shifter and cables, and k series itb's and aftermarket cams (skunk,toda,etc) would consider a complete head with...

Fitting the euroR head to my closed deck block (h22a) which type of gasket do I use as the head is off an open deck engine, I'd assume the gasket would need to match the block but just want to be sure,

Was going to order a new shifter and cables but thought id stick this up incase anyone has one lying around, would save me a bit in delivery times, and avoid getting stung on imports tax,

Anyone know where id get ngk heat range 8 plugs, part no: R5671A-8, local autofactors cant get them, :/... Need two sets so 8 in total

Looking a gasket for the h22, its drawing air between maniford and head so wont idle properly, dosnt matter to me if its thermal or standard, but id assume an oem one would stick boost pressure better,

Are all walbro fuel pumps universal? Looking for one for my cl1 euro R, but cant find one listed anywer, but can easily get a civic one, so if they are the same id get away with that.

just after figuring out my ek9 must have been stroked as the rods out of my mangled engine are p72, and the revlimit was 8400. can the ecu boards be swapped in stock ecu's? as mine still has the pct part number on it. is there any identification on the circuit board i can go by if i take off...

had a bee-R limiter in the cl1 the last month or so, was using it as flat shift wired to the clutch pedal, worked good didnt have to lift off to change gear, and spat a flame out each tailpipe on every gear change, but this is the result, its not a rumour that they are engine killers it is a...

Anyone know where to buy seat material, want to retrim my fixed back bride to match my recaro

want to buy big end bearings for h22a accord euro R, its urgent and i havent got time to wait 2 weeks on the local dealer ship, any where have them in stock?

urgently need a set of rod bearings for the euro R, dosent matter either acl, or genuine honda, maybe someone could advise me where to order that i wont be waitin all week on them to arrive, thanks

Is there an active vendor for hardrace on the forum? Lookin to buy a bushing set and camber kit, i pm'd dixelbrake as they are suposed to be vendors but got no reply,

What polybush kit should i use for a k20 track car, im useing a dc2 subframe so do i need a dc2 front kit and ek9 rear or do they have the same rear suspension? If they do then a complete dc2 kit will fit,

As above im looking to buy a bride cover, Finally managed to find my self a fixed back bride, Looking to buy a new cover preferably red,As my side bolster is busted, I know covers for recaros or sparco as easily enough sourced, so does anyone know if i can buy a new cover direct from bride,

Combidrift - YouTube proper tidy driving imo, unlike block their isnt hundreds of tyre marks from practise or any special effects, just two proper nutters, :lol: sorry if this is a repost, but i dont think iv seen it on here before,

been missing driving the ek9 real bad, so was watching a few video clips of it in an attempt to put a smile back on my face, jus thought id share it with you guys too, :) ek9 b16b acceleration - YouTube