Search results


  1. Joshm88

    Civic Coupe (EJ8/EM1) No Rust (Black preferred)

    Hello All, It's been a while since I was last on here so it's good to be back! I'm looking for a civic coupe EJ8, EM1 or similar (but pre-facelift EJ8 preferred) to replace my current EJ8 which is beginning to rust on the rear arches. Vehicle exterior and shell must be in GOOD...
  2. Joshm88

    FS: *Breaking* CW EK9 (prefacelift)

    Pre-facelift CW EK9 being broken. As far as I know this is the latest pre-facelift EK9 in the UK (see Dunx ek9 register thread). Condition is excellent, the only reason for breaking is due to change in personal circumstances. Car is based in Manchester, all parts are available, only the main...
  3. Joshm88

    EK9 engine loom + fuse box

    As title suggests, I'm in the market for a pre-facelift EK9 engine loom (dash loom not needed). Also after a jdm EK9 fuse box. What you guys got :)
  4. Joshm88

    A bit of ABS help please...

    I did a rear disk conversion on my EJ8 (pre-facelift EK coupe) a while back. The hubs were off an EG6, but did not come with ABS sensors. The drum ABS sensors off my old hubs were a perfect fit, so at the time I decided to connect them to see if they would work (long shot I know). They...
  5. Joshm88

    OBD2A ECU pin out voltages?

    Does anyone have the individual voltage/resistances for the ECU pin outs? Also, what pin out is measured for the oil pressure switch sensor on the back of the block? I've looked through the pin out data and can't seem to match it up. I read something about checking the EVAP purge control...
  6. Joshm88

    Civic coupe shell (black)

    Total long shot..... but in the market for a black civic coupe (EJ8/EM1, so EK shape). Had one lined up to break, but sale fell through! Keep browsing autotrader/ebay etc, but need one with absolutely NO RUST, especially on the rear wheel arches inside and out, and no rust on rear quarter...
  7. Joshm88

    Replacing my shell, bit of help?!!

    Finally decided the rust on my rear arch is not worth trying to fix, it will just come back anyway eventually! So I'm going to buy a new shell and swap everything over. Found another EJ8 up for sale, in black for £500, which I thought isn't bad! Plus it's local! Exterior is a bit of a mess...
  8. Joshm88

    WTB: J's Racing carbon canards

    Possibly in the market for J's Racing carbon canards (EK9), damaged one of mine, unsure as to whether it can be repaired. Let me know if you have any..................:thanks:
  9. Joshm88

    Definitely F*%ked

    No words really..... :angry2: So yeh...I don't think J's Racing sell canard individually :((
  10. Joshm88

    J's Racing exhaust Group Buy

    VENDOR HAS SENT PM'S TO ALL CONCERNED Anyone expecting one who hasn't received one let me know ASAP!!! Hi guys, Just posting this up to see if anyone is interested in ordering a J's Racing exhaust (Brand New). The order will be placed in April/(early May at the very latest). The group buy...
  11. Joshm88

    Brockway Engineering Race data display?

    Been looking at getting one of these, Kingmotorsports have the R920 version on sale at $159. I was planning on investing on an AFR gauge, but if this incorporates AFR amongst a tonne of other features, read from the ECU, was thinking of going for this. Has anyone had any experience with...
  12. Joshm88

    Ongoing idle issue (vid added)

    A quick video I took to demonstrate part of my ongoing idle issue. This is of the car when cold, on high idle (1500/1600). The car is sat at idle, I am depressing the brake pedal, then letting off, when I am letting off the revs jump up to around 2000rpm before dropping back to 1500/1600. Is...
  13. Joshm88

    Cambelt too tight?? (Vid added)

    Got a high whirring sound coming from the belt area in the bay, thinking it could either be a bearing that is knackered or an over-tensioned belt. When I had the motor put in, my tuner said he checked the tension on the belt and it was fine, tensioner was also fine.....but doesn't sound healthy...
  14. Joshm88

    Little Exhaust advice...not impressed

    Right, I bought this exhaust off a member on here and have a few questions. The B-pipe is in awful condition and will not be going on my car, the seller has been contacted (awaiting reply) as it was advertised as "very good condition", yet there are a number of holes on the welds. My main...
  15. Joshm88

    FS: Cheap steering wheel, Blitz oil pressure gauge, temp gauge

    Item for sale: Blitz oil pressure gauge + Timex oil temp gauge Reputation: http://www.ek9.org/forum/reputation-center/29372-joshm88.html Price: £35 + delivery Paypal?: Yes (send as gift or buyer pays fees) Location: Manchester Condition: 9/10 Description: Never installed as I ended up...
  16. Joshm88

    FS: Pre-facelift grill (rep)

    Item for sale: Pre-facelift EK9 Grill (replica) Reputation: http://www.ek9.org/forum/reputation-center/29372-joshm88.html Price: £35 + postage Paypal?: Yes (as gift or buyer pays fees) Location: Manchester Condition: 9/10 (one small clip broken but makes no difference when fitted) Description...
  17. Joshm88

    Jasma stamp identification

    This is taken from Mcr-Vtec, credit goes to member Sinbad over there! Have had it saved for a while but thought it might be useful to others on here! If you look at the first 3 numbers of the Jasma number on ur exhaust you can identify the maker. Akiyure Inc. 047 Apekusera Inc. 048...
  18. Joshm88

    ASAP!!! Rear ABS sensors COMPLETE EK4/EK9

    As title suggests, need to rear EK4/EK9 ABS sensors complete, not cut! Need asap, but not too urgently where I'll pay stupid money for them....:secret: What you got?! Cash waiting, could do with them posted today....
  19. Joshm88

    Rear EG and EK4 rear disc 4x100 hubs the same?!

    Right, ignore the title as it's not exactly what I'm asking! Since having installed the rear disc conversion with EG hubs/brakes on my EJ8 (EK chassis), my ABS light has been on......most of the time. My rear ABS sensors were for drum brakes, but the sensors seem to fit to the rear disc hubs...
  20. Joshm88

    Rigid Subframe Collar - gauging interest (forum members only)

    Right I have a set of Spoon rigid collars in my possession which I have had sent off to a University metallurgist who has determined the exact composition. A very good friend of mine has access to a full machine shop since his dad owns a reverse engineering business. I am considering...
Back
Top