Honda Civic EG6 SiR 2 - JDM - Build / Project / Restoration


Teeky_JDM

Active Member
Joined
Mar 13, 2019
Messages
136
Car(s)
MB6 VTIS
Not so very overnight parts from Japan!

Been waiting for quiet some time for these to land, took the absolute piss!! But anyways here they are.....

Honda Access OEM EG6 SiR mats

Full set of 5

Driver's side still has the little white tag on it, even though your supposed to rip it off lol

They looked okay in pics but they are actually MINT!

Absolutely over the moon with them! Got them at going rate too :)) so not to bad lol

Gonna give them a propper clean later on.

FB_IMG_1563248315428.jpg


FB_IMG_1563248317561.jpg


FB_IMG_1563248319750.jpg


FB_IMG_1563248321709.jpg


FB_IMG_1563248323750.jpg


FB_IMG_1563248325808.jpg


FB_IMG_1563248327882.jpg


FB_IMG_1563248329889.jpg


FB_IMG_1563248331930.jpg


FB_IMG_1563248334219.jpg
 

Last edited:

Teeky_JDM

Active Member
Joined
Mar 13, 2019
Messages
136
Car(s)
MB6 VTIS
I took the front wings off to see what it's like, driver's side has a little bit of surface rust, passenger side has some but not as much, for some odd reason the passenger side is alot cleaner then the drivers side in general lol, maybe the drivers side was parked next to a tree or next to a drain or something, looks like alot more water has been around the drivers side.

FB_IMG_1563277747008.jpg


FB_IMG_1563277762802.jpg


Should just be able to grind it off and rust treat it.
 

Last edited:

Teeky_JDM

Active Member
Joined
Mar 13, 2019
Messages
136
Car(s)
MB6 VTIS
Time to remove the sound deadening!

Bought a few cans of MOTIP Freezer spray, its basically dry ice in a can, cheaper and works alot better!

All you gotta do is spray the sound deadening, give it a couple of seconds and then get a hammer or mallet and smack it lol, and the sound deadening is off!

Really clean job, no tiny bits left over or anything, I got the whole Interior done in about an hour lol.

Unfortunately I found a couple of rust spots! One behind the driver seat, just Infront of the seam seal, and the other in the drivers footwell next to a grommet.

I also noticed that the sound deadening holds alot of water underneath, so I'm probably not going to put any back in!

Still need to get pics of the car once it's cleaned up from inside, might even weigh the sound deadening and see how much I've taken out :dance:

FB_IMG_1563277709930.jpg


FB_IMG_1563277713491.jpg


FB_IMG_1563277716424.jpg


FB_IMG_1563277720735.jpg


FB_IMG_1563277723567.jpg


FB_IMG_1563277726550.jpg


FB_IMG_1563277728806.jpg


FB_IMG_1563277775458.jpg


FB_IMG_1563277777898.jpg


FB_IMG_1563277780763.jpg


FB_IMG_1563277786946.jpg


FB_IMG_1563277794474.jpg


FB_IMG_1563277797078.jpg


FB_IMG_1563277789467.jpg


FB_IMG_1563277792234.jpg
 

Last edited:

Teeky_JDM

Active Member
Joined
Mar 13, 2019
Messages
136
Car(s)
MB6 VTIS
Finally got some spare time, so I got my arches & sills and took them down to the unit and gave them a "MOCK" up lol

They aren't sat on the car properly that's why the mouldings and sills don't look flush, but they are good fitment.

Can't wait to strip it and make some progress!

FB_IMG_1563750355348.jpg


FB_IMG_1563750362372.jpg


FB_IMG_1563750368424.jpg


FB_IMG_1563750377293.jpg


FB_IMG_1563750371641.jpg


FB_IMG_1563750373829.jpg
 


Top