Si's second attempt at a DC2


Progress has been pretty slow in all honesty, but then again I'm not exactly on a deadline so it doesn't matter too much.

Once I had finished with the bonnet hinge area I moved on to the arch. Few bit of surface rust were removed and treated. I then either made a sound decision...or a really stupid one that I didn't need to.

Where the car had been undersealed previously on the arch, it was beginning to dry up, and flake away in places. I thought the best idea would be to just get it all off and start again with fresh protection. (I thought it would all just come away from the paint with ease.)

Proceeded with using a scraper and removing the flaky scabby bits. Wasn't quite as easy as I hoped, and there was still a load stuck on the car.

20171209_133707-3024x2268.jpg

20171209_141748-2268x3024.jpg


I soon realised the under that flaky layer was a thick oily tar like protection. In the end I used about 2 bottles of tar and glue remover and too many hours of cleaning than I care to recall. :busy:
20171210_143530-2268x3024.jpg


But I got there in the end, and more good news in that there is no corrosion under there either. I think it may have stained the seam sealer, or is it normally that colour?
20171215_150059-3024x2268.jpg

20171215_150038-2268x3024.jpg


Other than that I've just started on the front end bits before taking care of everything on the passenger side.

I'm playing a bit of a waiting game at the minute as I'm prepping all of these areas for undersealing, but the product I'll be using for protection (epoxy mastic) can't really be used under 10 degrees. There's no chance I can heat up the unit enough with the roof being so high.
However a mate of mine is going to be re painting the bonnet hinge areas champ white for me at some point, and he's offered me access to his lamp heaters over the festive period whilst he's not at work. So I think the best idea would be to utilise them and get as much finished as I can during that time frame.
Once he's back at work I think the best idea would be carry on prepping a part at a time and hope that when it comes to finishing off the job its heated up a bit!

Anyway away from that I finally went and got my manifold polished up. I couldn't be bothered with it in the end and wasn't getting the results I was after. Few days turnaround and I got a reasonable finish on it. It's not 100% but I guess it's probably not going to stay shiny for very long anyway lol

20171212_183214-2268x3024.jpg

20171212_183153-2268x3024.jpg


Anyways, enough blabbering. Thanks for reading :)
 

Attachments

  • 20171209_133727-3024x2268.jpg
    20171209_133727-3024x2268.jpg
    1.5 MB · Views: 361
  • 20171212_183131-2268x3024.jpg
    20171212_183131-2268x3024.jpg
    1 MB · Views: 372
Nice updates. The seam sealer has probably been stained by the under body protection that was applied to it.

Would love to have the space to do that to mine. Single garage makes it hard work!
 
Nice updates. The seam sealer has probably been stained by the under body protection that was applied to it.

Would love to have the space to do that to mine. Single garage makes it hard work!

Yeh I was in 2 minds to remove it and re apply some fresh sealer, but the oil in the underseal seems to have kept the original stuff from becoming brittle and cracking. So no real need to be honest.
Although there are a lot of areas where 2 (or more) sheets of metal have been spot welded together and no seam sealer applied. I'm not sure if I should seal those areas up now, or if they are required for drainage and what not?

Ah tell me about it! I lost half my garage to make way for a dining room, so no chance I can even get a car in there anymore. :( I'm glad I managed to find a unit when I did as I want to get this job done and out the way with.
Not sure how long I'll keep hold of it though, as it's a lot of money to fork out every month and I'm splitting the cost with someone, who may not continue to rent it after the winter has been and gone. :nerv:
 
Yeh I was in 2 minds to remove it and re apply some fresh sealer, but the oil in the underseal seems to have kept the original stuff from becoming brittle and cracking. So no real need to be honest.
Although there are a lot of areas where 2 (or more) sheets of metal have been spot welded together and no seam sealer applied. I'm not sure if I should seal those areas up now, or if they are required for drainage and what not?

Ah tell me about it! I lost half my garage to make way for a dining room, so no chance I can even get a car in there anymore. :( I'm glad I managed to find a unit when I did as I want to get this job done and out the way with.
Not sure how long I'll keep hold of it though, as it's a lot of money to fork out every month and I'm splitting the cost with someone, who may not continue to rent it after the winter has been and gone. :nerv:

I would imagine it doesn't have seam sealer applied its possibly for drainage.

I would love a local unit to me but they are just so much money!
 
Christmas period over with and was back at it. Slightly annoyed how little time I got on the spend working over the 2 weeks of holiday I had, but hey ho.
Finally finished both wheel arches now, all ready to be undersealed and protected again. No nasties to report on again, nice and clean. :)
Was a bit frustrated with how long it was taking me...hence the picture.

20180109_172430-2268x3024.jpg


Strut tower again was all good, just stained.
20180109_172117-2268x3024.jpg


Ive taken the majority of the seam sealer around the passenger side bonnet hinge area as well, again same scenario as the drivers side with rust underneath it. So I'm glad I've gone to these lengths.

20171229_132916-2268x3024.jpg


I'll be tackling this and a couple of tiny isolated areas of the passenger wing where there is a small amount of surface rust and then the entire front end is ready for underseal :D I have finished the slam panel as well, but didn't get any pictures.

Was browsing eBay last week (as you do) and stumbled across a pair of wheels. Original Kosei P1's (Budyclub's) in 16X7.5J ET32. So slightly more aggresive offset than the Advans. Will be using these on the fronts, but don't have any hubs on at the minute obviously so did a test fit on the rear. With a proper sized tyre and some camber they should fit easily up front. Absolute bargain at £180!! Couldn't pass them up as they were only 45 minutes up the road!
These were being used to roll a Toyota Chaser around, hence the chunky tyres.

20180109_154420-3024x2268.jpg

20180109_155601-3024x2268.jpg

20180109_155719-3024x2268.jpg
 
Small update, the vast majority of the front end is fully rust treated and is ready for sealing. :))
Once I had finished both bonnet hinge areas, I primed them and tiger sealed them up. A mate of mine who paints for a living then came in and painted the scuttle and hinge areas.

20180127_142556-3024x2268.jpg


You can see here the tiger seal I've put on. It isnt the best job, I tired my hardest to copy the oem lines and thickness but applied a bit more sealant in the areas that were missed from the factory. It doesn't overly matter too much though as once the scuttle is on and the wings, you can't see any of it anyway!

20180127_161956-3024x2268.jpg


Took all the plastic sheeting off once the lacquer has been sprayed and waited for it to fully dry.

20180127_161945-3024x2268.jpg



My mate has been kind enough to loan me his heat lamps during the weekends so I can start cracking on with the undersealing, as the products I'm using really don't react well with cold temperatures.
I'm going to do it in 3 stages, 1 arch, front slam panel then passenger arch. So made a start on the drivers side front arch today. Primed with Bilt Hamber's Electrolux, really strange texture primer but easy enough to use.

20180128_143210-3024x2268.jpg

20180128_165448-3024x2268.jpg


Needs to be left for 3 days apparently before overcoating with high solvency top coats. So come the weekend I will be putting down the underseal.

Got a massive order of Hardrace bushes in place that should be here next week. Also going to get my arms shot blasted once I get paid, then they can get some epoxy mastic before being put back on the car.
Everything is slowly coming along. I'll see how I'm getting on for time but I may leave doing the back end of the car until winter 2018.
 

Attachments

  • 20180109_172117-2268x3024.jpg
    20180109_172117-2268x3024.jpg
    1.3 MB · Views: 346
Got home from work during the week to a big delivery of Hardrace parts. I used a company called RHD Performance for the 1st time, think they maybe a new company as I couldn't find out an awful lot of information on them, but really good experience.
Beat all the other main competitor prices by a nice chunk (Including "Hardrace UK" ironically). Free shipping for all this lot and great communication. I'll be using them again for sure.
Their website is here: https://www.rhdperformance.co.uk/ They can get the entire catalogue of Hardrace (amongst other brands), but haven't got around to listing everything they sell.

20180201_204744-2268x3024.jpg


But that's basically everything for the front end that I require to build the car back up with new suspension parts. :D I'll list it all once it's on the car.

Dropped by a local powder coaters to me and decided to get my suspension arms shot blasted. I decided not to take my knuckled in as they still have the wheel bearings in and didn't want them getting grit in the bearing...or is this being overly cautious?
But 45 minutes later and £30 I'm glad I didn't waste my time with wire wheels. lol

20180203_163742-2268x3024.jpg



I decided not to underseal that 1 arch I did last weekend, but instead chose to get the whole front end primed up. Was going well until I ran out of paint. :angry2::angry:
But I got the slam panel finished with 2 coats and the passenger arch is half done on it's 1st coat. lol

20180203_165701-3024x2268.jpg


Final part I picked up was a new CV joint for the passenger drive shaft. I now found I can use a EP3 outer CV joint on 98 Spec hubs, so that's nice and easy to get hold of if I need some in the future.
Cut the boot off and tried hammering the joint off, but will need to use a vice really as it's not budging. The CV grease has also turned a delightful green colour. :eew:

20180203_172215-2268x3024.jpg


Got a big order of OEM parts on the way including windscreen mouldings amongst other bits.
 
Long weekend at it but I feel I've made a lot of progress :))

Basically I have the majority of the front end undersealed now, the exception being the underside of the slam panel (where you jack the car up) and a couple of areas just between the wheel wells and subframe.

The epoxy mastic stuff from Bilt Hamber is easy enough to use, mix it up and brush it on. But the consistency is really weird, it's really tacky and as such trying to get a nice smooth finish I found quite difficult. The black version I've used on the wheel wells went on easy enough, only needed 2 coats and it covered up the primer and has a nice finish to it.
I'm not too sure on the white in all honesty. It looks better in the pictures than it actually does in person. I applied it quite thinly, but it took about 4 coats of the stuff to cover up the primer and be solid white (there are areas where it still looks a little patchy that will need a touch up).

I really can't make my mind on wether I like the white, but I can't particularly be bothered on changing the colour of it now, but what do you guys think? Keep the contrast of the black and white? Or paint everything not on show black. I keep telling myself the overall finish of the product it's massively important as it's not on show....but it will just bug me lol

Anyway, I will put some pics

20180211_144206-3024x2268.jpg


20180211_144132-3024x2268.jpg


20180211_144145-3024x2268.jpg


20180211_144155-3024x2268.jpg


So from here I've got a few more jobs to do before the rebuilding of the front end starts. Front bumper support and crash bar are away for shot blasting and powder coating. I still need to sort my CV joint and get the bushes in my LCA pressed in. A quick wire wheel of my hubs and a lick of paint and some stone chip to go over the high impact areas on the arches and then I'm ready. :)
 
Nice updates. Really need to give my shell some love. Just don't think I have the time for this.

How long has the above take you?
 
Nice updates. Really need to give my shell some love. Just don't think I have the time for this.

How long has the above take you?

I have a higher level of respect for people who do this sort of thing for a living as it's a massive ball ache tbh haha
I'm so bored of it now that once the front end is finished and back together I'll leave the rear until later this year.

All in all I started in November, and looking to have it finished by March. I've took my time with it and I've only been doing a few hours here a weekend there so no idea how many man hours tbh (not quick though)
 
Oh yeah I couldn't do it on a daily basis!

Really tempted to buy a cheap EK shell and send it to be dipped and then have a cage welded in. Then just reshell and respray.
 
Had a bit of leave from work to use up that I've not been able to use until now, so booked off 2 weeks starting at the beginning of this week. Plan was to smash out the re assembly of the DC2 and get it back on the road for the upcoming spring and summer. Managed until Tuesday when I got the dreaded call...long story short I've been "emergency deployed" to Bahrain for 3 months. With 10 days notice. Joys of the armed forces...

So after much swearing and moaning I set to work getting the DC2 back into a state where it could easily be moved around the unit as Mitch will be needing to get his CRX in and out whilst I am away, so mines getting tucked up in the corner.

Car looked like this with the crash bar and bumper support being the only bits I had put back on the car when I received the phone call.

20180218_182014-3024x2268.jpg


Fast forward onto Wednesday and I had all the new suspension bolted on, torqued down, exhaust manifold on, shift linkage back on and the car back on all 4 wheels in about 5 hours (quite good going for me as I don't like rushing things)

20180228_203112-2268x3024.jpg

20180228_203733-3024x2268.jpg

20180228_204642-3024x2268.jpg


Hooked up the battery today and turned over the engine, fired up straight away on the button after standing for 4 months :)
I really wanted to roll it out the unit and just take it for a quick spin up and down the path to the unit (yes with no body panels lol). Opened the door and was greeted with 2 inches of snow! Great. I'll have to leave that till next week before I fly out.

I should be home early June, and my plan is to get all the panels back on the car in time for Players Classic at Goodwood on the 24th June as I've been accepted into the show, and it's one of my favourites and local.
After that I will spend some time getting on the small stockpile of mods I have for the car.

Mega disappointed about going away as I had loads of plans for trackdays this year as I haven't been able to do any since my 1st in June 2016 (due to being away with work again). A few mates have the Nurburgring booked in July, so I may tag along if I can afford it once I get back. :p
Biggest bonus of this time away is that they are giving me a temporary promotion = more money. :)

Until that time, this is likely to be the last update from me, will update you when I get back to working on the car again in T-minus 97 days...
 
Big update from me. (Picture heavy)
I've neglected this site a bit since I got back to the UK, as I've discovered the wonders of Instagram. lol
I was eventually persuaded to open an account by my mates after years of insisting that I don't take good enough quality photos for it.
I'm glad I use it now as a lot of builds are no longer on the likes of these forums anymore to follow :( But I thought I should carry it on here, as this has been a source of such good information over the years :D

So got back from my deployment in the middle east pretty much to the exact day I was expecting (quite surprised) and wasted no time at all in getting the DC2 back together. I had a 2 week window prior to the first show I had booked to attend, Players Classic at Goodwood.
Last few jobs were,
  • All 5 engine mounts replaced (what a pig of a job the rear one is!:mad:)
  • Rear coilovers and camber arms installed
  • Defi gauges wired up
  • All the body panels put back on
Rear engine mount had seen better days:
IMG_20180609_140232-2592x3456.jpg


Replaced all round with Hardrace ones:
IMG_20180609_140256-2592x3456.jpg


Coilovers and carmber arms are so easy to install on these cars:
IMG_20180610_175647-2592x3456.jpg


How the car was looking after day 1:
IMG_20180610_175736-2592x3456.jpg


Defi gauges are literally the easiest thing ever to wire up.
IMG_20180706_150059-2592x3456.jpg


I think it took about 1 week and the car was up and running with another years MOT put on her followed by an alignment :p

Got a quick picture on the Friday night when it was all complete alongside my mates JDM EP3.
IMG_20180612_212144-3456x2592.jpg

IMG_20180612_212048-3456x2592.jpg


Players Classic was a bit of a hit and miss show for me this year, 2 day event that didn't seem to bring in the volume of people compared to previous years. I might give it a miss next year.

After that way Summer Action day at Castle Combe. I decided to have a couple of 15 minute stints on track as a taster for the DC2. Not a great decision in hindsight as it was way too busy on track, plus thousands of people watching lol
Basically understeered onto the grass on my 1st lap due to forgetting about cold tyres :oops: Then spun out on Quarry corner (worst corner there) due to lift off oversteer :nerv::lol:
Was eventful to say the least, but the car and I came away unharmed and I learnt a thing or two about how the DC2 handles on track. lol

Decided to play it safe with the rear wheels as I wasn't sure if the Advans were going to rub so opted to run the OEM's on the rear for peace of mind.

IMG_20180706_173954-3456x2592.jpg


On the subject of wheels I did a bit of a trade with someone local to me and swapped my Buddyclub P1's in 7.5J for a pair of his 7J's.
He also had a pair of TE37's for sale as well, which I couldn't resist at the price he wanted :dance:

P1's will be going on the rear (16X7 +43)
IMG_20180714_150350-2592x3456.jpg

IMG_20180714_150411-2592x3456.jpg


The TE37s on the other hand, maybe a bit of an ask to fit. (16X7 ET25) with -2 degrees of camber:
IMG_20180714_145516-2592x3456.jpg

IMG_20180714_145709-2592x3456.jpg


We had a pretty cool collection of wheels going on between the 2 cars. :cool:
IMG_20180714_152018-2592x3456.jpg


I took the balloon tyres off the Volks and tried on a 215/45/16...
IMG_20180718_165735-2592x3456.jpg


Still a bit too much poke. Im going to try a 205 tyre out and see if it fits, I also have -2.5 degrees of camber now since that last trial fit.
IMG_20180718_165613-2592x3456.jpg


The last show really for me of 2018 was Simply Japanese at Beaulieu. Unfortunately after all the wall to wall sunshine the UK had been experiencing for the past month came to a halt and it decided to hammer it down all day. :(
Still my mate Mark and I braved it as its only 30 minutes down the road.

IMG_20180729_141635-3456x2592.jpg


Will follow on the updates in a second post.
 

Attachments

  • IMG_20180714_145523-2592x3456.jpg
    IMG_20180714_145523-2592x3456.jpg
    1.6 MB · Views: 306
Following on with a more recent update, I finally got my summer leave off work confirmed just in time to be able to tag along with a few mates on a trip to the Nurburgring!:dance::))
My 'Ring prep' consisted of an oil and filter chnage along with a brand new Fujitsubo RM01A exhaust as my existing one was way too loud for me and a 1000 mile round trip was the perfect opportunity to upgrade :naughty:

What an experience that place is! Even the surrounding roads are insanely fun let alone the track! I didn't go too hard on track as it costs a fortune if you have an accident and its quite a challenge to try and remember every corner.
In the group we had a DC5, EP3, JDM EP3 and Audi S3 (He owned 3 Integras over the course of 8 years previosly so we will let him off lol)

Pulled over for a quick picture at one of the viewing car parks:
IMG_20180807_161953-3456x2592.jpg

IMG_20180807_161846-3456x2592.jpg


Of course, going to the Ring, you have to take the picture outside the sign.

One of all the cream cars lined up:
IMG_20180808_123300-3456x2592.jpg


Also got one with just the Integra's:
IMG_20180807_163652-3456x2592.jpg


The trip wasn't all sunshine and roses unfortunately. On the 2nd day on his 2nd lap my mate had an accident in his EP3. :( Cost him a pretty penny not only for the crash, but also recovery to the UK.
IMG_20180807_201119-2592x3456.jpg
IMG_20180807_201103-3456x2592.jpg


Engine mount had snapped clean off the driver side, rad leaked out all of its coolant and the chassis leg had twisted on the passenger side.
Luckily for us we had the Audi to tow it back to the hotel.
Once the car is back and broken with all the parts sold, he should see a bit of profit in the end.
He's got the right mentality though and aims to get an EK9 and k swap it using the engine and box from the EP :)
Of course, we couldn't have a group picture without all the cars there, so as we towed the civic back we stopped off for a picture outside the sign. (The skyline at the back wouldn't move out of the picture o_O)
IMG_20180807_210109-3456x2592.jpg


Anyway, we met up with another group of lads who were also over for the week. One of them who is a photographer kindly took some pics of all the cars together. Really nice quality!
IMG-20180814-WA0000-962x641.jpg
IMG-20180814-WA0005-1200x800.jpg
IMG-20180814-WA0002-962x642.jpg


After the track session that evening we went and grabbed some food with them and got a cool picture of the train of cars coming down the forest roads.
received_2067206809970323-1512x851.jpeg


Final 2 pictures from the trip, of my mate and I going round the karussel, these were paid pictures from some of the many photographers based over there.

IMG-20180813-WA0000-962x641.jpg
IMG_2346-4104x2736.jpg


All the cars performed faultlessly! Not one hiccup and we even had a few days in Amsterdam after the ring. 1200 miles covered in total.

Only thing it highlighted to me was my oil temperatures are getting way too hot on track. 35degree celcius ambient temperature at 6pm with a track temp of 49 didn't help! :shocked:
But after a bit of advise I'm swapping out to 10W50 oil and also will be investing in an oil cooler in the near future.

I also tried to have the car mapped earlier this month and annoyingly the 2nd hand P28 ecu I bought was faulty and means I need to buy a new one. :mad:
Other than that I would ideally like to have the box refreshed and try out a 4.9 final drive with 96 spec 4th & 5th gears. But all in due course.
 

Attachments

  • IMG_20180807_201110-2592x3456.jpg
    IMG_20180807_201110-2592x3456.jpg
    2 MB · Views: 319
  • IMG-20180723-WA0002-962x721.jpg
    IMG-20180723-WA0002-962x721.jpg
    164.1 KB · Views: 319
  • received_448490465645008-1512x850.jpeg
    received_448490465645008-1512x850.jpeg
    387.6 KB · Views: 324
  • received_2204024049874188-1512x851.jpeg
    received_2204024049874188-1512x851.jpeg
    331.1 KB · Views: 348
The Nurburgring is an awesome place, we were there in July in 2 EP3’s and a Golf GTI and I want to get back out again already

With the Oil, you should imo stick to the 10w40 or 5w40 and fit the oil cooler, your engine wasn’t built for a thicker oil

What happened to your mate in the EP3 that he crashed? Pushing too hard?
 
The Nurburgring is an awesome place, we were there in July in 2 EP3’s and a Golf GTI and I want to get back out again already

With the Oil, you should imo stick to the 10w40 or 5w40 and fit the oil cooler, your engine wasn’t built for a thicker oil

What happened to your mate in the EP3 that he crashed? Pushing too hard?

I've been back a week and already want to go back! :beer: haha

Regarding the oil, this was advised to me after a lengthy chat with Opie Oils. What I will most likely do is run this oil for a while until I get the cooler sorted then change back down to 10W40. Will see how the car behaves with the different oils.

Where the 5W40 is so thin I'm getting up to 120degrees within about 2 laps of Combe. Annoyingly going around the Ring I was having to ease off and coast the car in places as the oil way getting way too hot.

Not particularly I don't think, he hit a bump in the road whilst turning, causing the rear end to go light which gave him some understeer, but he couldn't correct it in time.
My mates Go Pro video from the JDM EP3, you can see him go sideways around the corner from the rear view mirror and then disappear.

Think the worst thing is none of the airbags even went off! :shocked:
 
Regarding oil, I'm still on oem laminova and using 5w40 ester race oil. I'm able to do 45minutes flat out at Rockingham and still staying just under 120 degrees constant with no issues.
I was able to drop 10 degrees in comparison to normal 5w40 fully synthetic.
Personally I feel there's no need for a external cooler with the right setup.
Hope this helps
 
Back
Top