Left (passenger side) knuckle


nashville

nashville

Active Member
Joined
May 27, 2020
Messages
117
Car(s)
1998 EK9
Mine has a slight bent. Would like it as bare as possible. I need the JDM passenger side or usdm drivers soxd
IMG_4081.jpeg
 
Is ek9 and usdm ek the same? Besides the hubs of course
 
262 factory disk EJ9, ej6 etc knuckles are the same,

I did abit of research last week as i was bored, the bearing part number on ek9,dc2 96 spec and uk spec, mb6, 262 ej9,ek3,ek4

all have the same bearing part numbers which means the 5 stud hub bit goes into any of those.

cheaper to go scrap yard or get one from someone parting out a car

edit: I just see above someones already mentioned it hahaha
 
spikeyhairdude said:
262 factory disk EJ9, ej6 etc knuckles are the same,

I did abit of research last week as i was bored, the bearing part number on ek9,dc2 96 spec and uk spec, mb6, 262 ej9,ek3,ek4

all have the same bearing part numbers which means the 5 stud hub bit goes into any of those.

cheaper to go scrap yard or get one from someone parting out a car

edit: I just see above someones already mentioned it hahaha
Click to expand...
Wish I seen this thread or knew this info before buying 4 stud wheels.
 
terry_em1 said:
Wish I seen this thread or knew this info before buying 4 stud wheels.
Click to expand...
The rears are a different thing tho. i tried to see if part numbers matched but alot didnt.
not evan the trailing arms are the same. they mount the same but are all different

I do see honed development sell a slimmer nut that holds the rear hub bearing assembley and it converts 4x100 rears to 5x114

5 Stud Rear Hub Nut Kit - Honed Developments

The Honed five-stud rear hub nut kit to allow the installation of Honda DC2 Integra Type R five-stud hubs on four-stud Civic and Integra models.
honeddevelopments.com honeddevelopments.com

Again i was bored seeing if i could piece up a poor mans 5 stud conversion
 
spikeyhairdude said:
The rears are a different thing tho. i tried to see if part numbers matched but alot didnt.
not evan the trailing arms are the same. they mount the same but are all different

I do see honed development sell a slimmer nut that holds the rear hub bearing assembley and it converts 4x100 rears to 5x114

5 Stud Rear Hub Nut Kit - Honed Developments

The Honed five-stud rear hub nut kit to allow the installation of Honda DC2 Integra Type R five-stud hubs on four-stud Civic and Integra models.
honeddevelopments.com honeddevelopments.com

Again i was bored seeing if i could piece up a poor mans 5 stud conversion
Click to expand...
I'm already aware of the Honed kit. Just didn't know what to do with the front. Too late now :angry: Have some tasty wheels on the way from Japan.
 
spikeyhairdude said:
262 factory disk EJ9, ej6 etc knuckles are the same,

I did abit of research last week as i was bored, the bearing part number on ek9,dc2 96 spec and uk spec, mb6, 262 ej9,ek3,ek4

all have the same bearing part numbers which means the 5 stud hub bit goes into any of those.

cheaper to go scrap yard or get one from someone parting out a car

edit: I just see above someones already mentioned it hahaha
Click to expand...
sweet!

I was about to spend $300 on two fronts that I didnt need. thank you!
 
You must log in or register to reply here.
Back
Top