Will they fit!!!


kasperwhoo

kasperwhoo

New Member
Joined
Sep 17, 2009
Messages
318
I came across some oem prelude sh wheels and I was wondering if the lug pattern is 5x115 or 5x114.3? :nerv: And will they fit on the integra type-r suspension or civic type-r suspension or :angry: will I have to get prelude hubs and brake setup. :secret: I have heard that the prleude base model is 5x114.3 and the sh model is 5x115! What is true and what can I do. :dance: I'm going to go a little different, but still have a stock look. I really like them and they are going to get fully reconditioned if I can use them. :thanks:
 
Last edited:
Ive always thought the ek9 hubs are 5x100 :S i could most definately be wrong!

If they are 5x100 then you will have too change hubs.

Then you consider if its worth it for a set of prelude wheels mate
 
gtismurf said:
Ive always thought the ek9 hubs are 5x100 :S i could most definately be wrong!

If they are 5x100 then you will have too change hubs.

Then you consider if its worth it for a set of prelude wheels mate
Click to expand...

you are wrong indeed EK9 hubs are 5x114.
 
I understand that the CTR has a bigger hub and brake setup than the ITR. ITR has a smaller hub right or is the discs (rotors) just smaller!
 
kasperwhoo said:
I understand that the CTR has a bigger hub and brake setup than the ITR. ITR has a smaller hub right or is the discs (rotors) just smaller!
Click to expand...

Where did you gain your above information from?
 
Common interchangeability questions:
* 90-01 integras (except the type-r) and 88-00 civics with rear disc brakes are all interchangeable onto any ek, eg, ef, da, and dc chassis.
* integra rear disc spindles, compared to civic drums, are 7lbs heavier (per side of course.) civic spindles with discs weigh less, but i don’t know how much.
* ek9 and dc2 take the same front and rear brake pads and rotors, so if you spent a ****-load of cash on a ctr 5-lug suspension/brake swap, there’s your replacement parts.
* * legend calipers are similar to the prelude/integra-r/civic-r calipers, though since the legend had the caliper on the back, swap them left to right to keep the bleeder pointing up during bleeding. Legend gs calipers must be mounted on a civic knuckle with the bleeders pointing down because the calipers are directional (two unequal sized pistons).
* the civic 88-00 ex rotor is the 10.3" rotor on all ex model civics from 88-00 and the same rotor found on integras 90-01 (exc. Type-r).
* da and dc calipers are not the same.
* 94-96 integras all take the same front and rear caliper, rotor, pads. Why people think the gsr has better brakes i don’t know.
* 94-01 integras and 97-01 itrs use the same knuckle, and same wheel bearing.
* 98-01 integra gsr and itr models use a 1" master cylinder, and will bolt onto the 96-00 civic stock master cylinder and hardlines with no bending of brakelines, and the fluid resovoir is the same.
* 96-00 civics, all take the same brake booster. The 99 si and 96 cx both take the same brake booster.
 
kasperwhoo said:
I understand that the CTR has a bigger hub and brake setup than the ITR. ITR has a smaller hub right or is the discs (rotors) just smaller!
Click to expand...

The CTR has the same Brake set-up as the 98 spec ITR(282mm). The 96 Spec ITR has the smaller brakes (262mm)

Also the driveshaft is different on the 98 spec ITR(36mm) than the CTR(32mm). But the 96 spec ITR uses the same shaft as the CTR.

But the car's you mentioned (the CTR and 98 ITR) are both 5x114.3
 
Last edited:
JDMarron said:
The CTR has the same Brake set-up as the 98 spec ITR(282mm). The 96 Spec ITR has the smaller brakes (262mm)

Also the driveshaft is different on the 98 spec ITR(36mm) than the CTR(32mm). But the 96 spec ITR uses the same shaft as the CTR.

But all the stud paterns are 5x114.3
Click to expand...

96spec teg is 4x114 not 5x114.
 
The one's he mentioned are both 5x114.3 which is what i was reffering to. Which is why i qouted it in my post :)
 
:lol: Damn where is all the love :)) (no homo)! And where is all the info on my other posts :blinx:! Not @ Daz!
 
Just a little info for my people!!


5 x 4.5 (same as 5 x 114.3)

Acura

1996-2003 3.2 TL
1996-2003 3.2 TL Type S
2004-2009 TL
2007-2009 TL Type S
2001-2003 3.2 CL
2001-2003 3.2 CL Type S
1996-2004 3.5 RL
1997-2001 Integra Type R
2002-2009 RSX
2002-2009 RSX Type S
2004-2009 TSX
2001-2006 MDX
1991-1993 NSX - All Models
1990-95 Legend

Honda

1998-2009 Accord - All 5 Lug Models
1997-2001 Prelude - All 5 Lug Models
1995-2004 Odyssey - All Models
2003-2009 Element - All Models
2003-2009 Pilot - All Models
1998-2009 CR-V - All Models
2006-2009 Civic - All Models
2004-2009 Civic Si

4 x 4 (same as 4 x 100)

Honda

1982-1989 Accord - All Models
1980-2005 Civic - All 4 Lug Models
1982-1991 CRX - All Models
1993-1997 Del Sol - All Models
1986-1991 Prelude - All Models

Acura

1986-2001 Integra - All Models (except Type R)

4 x 4.5 (same as 4 x 114.3)

Honda

1990-2002 Accord - All 4 Lug Models
1992-1996 Prelude - All 4 Lug Models

Acura

1996-2000 CL 2.2
1995-2001 TL 2.5
1986-1990 Legend
1992-1994 Vigor

5 x 4.75 (same as 5 x 120)

Acura

2005-2009 3.5 RL
2007-2009 MDX - All Models
2007-2009 RDX - All Models

Honda

2005-2009 Odyssey - All Models
2005-2009 Ridgeline - All Models
 
You can also use only the S2K wheels......just need 2 sets of the front.
 
Hello, I plan to do a 5lugs swap on my 96 ITR, will the EK9's fit or do I have to get from ITR 5lugs hub and knuckles? Does DC2R's shaft bigger than EK9's? Or better yet I just look for DC2R 5lugs hubs and knuckles?

Thank you..
 
Last edited:
You must log in or register to reply here.
Back
Top