Search results

My demon is dead. I was perfectly installed. I was just making some idle tuning and suddenly neptune crashes. I restart the software but this time it couldn't connect to demon. When I open the ECU I realize the demon has no LEDs on, demo is dead. I will get a new one, but I want to know is this...

Hello guys, I have a very big doubt. How mutch power can handle stock sleeves? I'v seen A LOT of people on internet saying that his car made 300-350-400-450 and even 500whp with stock sleeves. In evans-tuning parts-chart it say that stock sleeves can handle up to 400whp. But here in my...

Hello, I need to know if the sprinfgs of a EK4 4dr (b16a2) are the same as the 3dr

Hello, I got a set of GSR cams but when i compared with my b16a cams i can't see any difference. The only difference is a letter, the b16a intake cam has a M and the other has a B Are these gsr cams?

Hello ! I need to know if i can user water/meth in my b16 turbo without a tuning. I only want it as a coolant, not to get more power. I have a stock internals b16a with 300whp at 13psi on pump gas. I got the AEM water/meth kit

Hi, it is safe to run 12-15psi with oem rods in a b16 engine?

Hi everyone, Here is my Civic VTI B16A2 turbo build with stock internals. Wiseco pistons 9:1 (Not used yet) Eagle rods (Not used yet) Tial Waste 38mm HKS BOV APR studs Injector Dynamics ID 1000cc Walbro 255lph fuel pump Spooling Performance cast manifold Garrett T3/To4b turbo MFactory LSD ACT...

Thats my doubt It will help spooling? It will shield the heat? of course yes It will affect the lifetime of the turbo? pros ans cons??

Ok, finaly my build! It is an 98 Civic Ek4 VTI with B16A2 engine. Stock internals ITR cams ITR IM Spooling Performance cast iron manifold Tial 38mm wastegate HKS BOV Garret T3/To4b turbo (to4e did not fit) Injector Dynamics 1000cc P28 Custom 2,5" downpipe Custom catback (no cat) ACT clutch...

Hello, I want to know if it is neccesary an extra vent for the block on my build b16a2 turbo, stock internals.

So, pretty much as the tittle how much power and boost can handle a b16a oem rods and pistons? Evans-tunning said up to 400hp, but it is hard to believe

Hello, I'm building a b16a2 turbo and i want to know how much power can i expect and how much boost can y use for a safely tunning, 91 octane fuel and methanol (maybe at 20%). So far the setup is: Cast manifol 38mm tial wastegate ITR cams ITR ported intake manifold 9,1 CR forged...

Hello guys, I have a civic HB 98 and i got a bi-xenon kit H4, but the lighting is wors than before with the regular bulbs. Does my car need H4 or 9003 bulb?

Hi guys!! Does anyone know where can i get one of this? YouTube - 96-00 Honda Civic Vadar Gauge Cluster

Hi everybody, Im Walo From Argentina and I own a Civic 98 Hatch EK4 with B16A2 in very good conditions. Actually with 175whp and with a turbo coming soon Stock internal ITR cams ITR ported intake manifold with termal gasket 62mm throttle body with termal gasket PowerChamber short ram...

Hello, Im going to biuld my EK4 hatch b16 turbo, but i don't know which is the best turbo for my requeriments. So far i have: Wiseco 9:1 forged pistons Eagle rod ITR intake cam 1000cc ID inyectors ITR ported intake manifold Walbro 355lhp Ferrea flat valves and i like to reach just...

WTB skunk2 stage 2 or stage 3 tuner cams for b16.

Hello, I am looking for a muffler for my ek but i really don't know much about these. Any recommendation for a quiet muffler with high flow. I saw something like this one, but it seems a little noisy and small 92-95 96-00 Honda Civic EG EK Twin Loop Muffler 98 99 : eBay Motors (item...